Results 71 to 80 of about 942,686 (360)
DESIGNING AND DEVELOPING A PROGRAM IN SINUMERIK vs. 1.3 FOR A SHAFT WITH SEALING GROOVES [PDF]
Fiabilitate şi Durabilitate, 2015 CNC is an abbreviation for „Computer Numerically Controlled". Numerically controlled tool machines are also called CNC machines.The numeric control results in a process of continuous „feeding” of an especially built programable controller, with a set ...
VALERIA VICTORIA IOVANOV
doaj
Investigation of tool geometry effect and penetration strategies on cutting forces during thread milling [PDF]
, 2014 The application of thread milling is increasing in industry because of its inherent advantages over other thread cutting techniques. The objective of this study is to investigate the effect of milling cutter tool geometry on cutting forces during thread ...
BRENDLEN, Romain +3 more
core +3 more sources
Design and analysis of a piezoelectric film embedded smart cutting tool [PDF]
, 2012 This is the author's accepted manuscript. The final published article is available from the link below. Copyright @ 2012 Institution of Mechanical Engineers.The condition of a cutting tool is an important factor for manufacturing processes.
Cheng, K, Rakowski, R
core +1 more source
Molecular Oncology, EarlyView.Following high dose rate brachytherapy (HDR‐BT) for hepatocellular carcinoma (HCC), patients were classified as responders and nonresponders. Post‐therapy serum induced increased BrdU incorporation and Cyclin E expression of Huh7 and HepG2 cells in nonresponders, but decreased levels in responders.
Lukas Salvermoser +14 more
wiley +1 more source
Machinability improvement using high-pressure cooling in turning
Research in Agricultural Engineering, 2014 Process fluids are used primarily for their cooling and lubricating effect in machining. Many ways to improve their performance have been proposed; the analysis of some of them is provided in the paper.
R. Drlička, V. Kročko, M. Matúš
doaj +1 more source
Molecular Oncology, EarlyView.This study integrates transcriptomic profiling of matched tumor and healthy tissues from 32 colorectal cancer patients with functional validation in patient‐derived organoids, revealing dysregulated metabolic programs driven by overexpressed xCT (SLC7A11) and SLC3A2, identifying an oncogenic cystine/glutamate transporter signature linked to ...
Marco Strecker +16 more
wiley +1 more source
Tool post modification allows easy turret lathe cutting-tool alignment [PDF]
, 1966 Modified tool holder and tool post permit alignment of turret lathe cutting tools on the center of the spindle. The tool is aligned with the spindle by the holder which is kept in position by a hydraulic lock in feature of the tool post. The tool post is
Fouts, L.
core +1 more source
Molecular Oncology, EarlyView.This study characterizes the responses of primary acute myeloid leukemia (AML) patient samples to the MCL‐1 inhibitor MIK665. The results revealed that monocytic differentiation is associated with MIK665 sensitivity. Conversely, elevated ABCB1 expression is a potential biomarker of resistance to the treatment, which can be overcome by the combination ...
Joseph Saad +17 more
wiley +1 more source
Identifying the cause of cutting tool failure by using simulation software
MATEC Web of Conferences, 2018 The article is focused on the construction problems of cutting tools designed for manufacturing components in high numbers. Analysis of the tool with low lifetime is provided with the use of simulation software to detect the causes of the tool failure ...
Zrak Andrej, Koňár Radoslav
doaj +1 more source
Reliability assessment of cutting tool life based on surrogate approximation methods [PDF]
, 2014 A novel reliability estimation approach to the cutting tools based on advanced approximation methods is proposed. Methods such as the stochastic response surface and surrogate modeling are tested, starting from a few sample points obtained through ...
Kolios, Athanasios +1 more
core +1 more source