Results 71 to 80 of about 837,527 (297)
Identification of Local Lubrication Regimes on Textured Surfaces by 3D Roughness Curvature Radius [PDF]
, 2014 This paper proposes a new method of 3D roughness peaks curvature radius calculation and its application to tribological contact analysis as a characteristic signature of tribological contact.
Bigerelle, Maxence +3 more
core +2 more sources
Molecular Oncology, EarlyView.We analyze cisplatin–DNA adducts (CDAs) and double‐strand breaks (DSBs) in a cell‐cycle‐dependent manner. We find that CDAs form similarly across all cell cycle phases. DSBs arise only in S‐phase. CDAs might not directly impair DSB repair, but S‐phase DSB lesions evolve in the presence of CDAs and disrupt repair in G2, also causing radiosensitization ...
Ye Qiu +10 more
wiley +1 more source
Practice of Cold Drawing Process Optimization of GCr15 Bearing Steel Rod
Teshugang, 2015 The effect of draft, cone angle and length of sizing belt of drawing die, and drawing speed on drawing stress and drawing surface accuracy of bearing steel GCr15 (1. 01% C, 1. 58% Cr) Φ11 mm rod coil has been analyzed. The optimization process for Φ11 mm
王莹莹, 杨鹏远
doaj
Experimental Verification of Speed Influence for Final Parameter of Drew Wire [PDF]
, 2013 Import 26/06/2013Tato práce se zabývá problematikou výroby wolframového drátu, kde je experimentálně ověřován vliv výrobní rychlosti na výsledné parametry drátu. Jedná se o výrobu taženého a čištěného wolframového drátu.
Jurásek, Robert
core
Vacuum Technology for Ion Sources
, 2014 The basic notions of vacuum technology for ion sources are presented, with emphasis on pressure profile calculation and choice of pumping technique. A Monte Carlo code (Molflow+) for the evaluation of conductances and the vacuum-electrical analogy for ...
Chiggiato, P.
core +1 more source
Mechanical properties of a degradable phosphate glass fibre reinforced polymer composite for internal fracture fixation [PDF]
, 2010 NOTICE: this is the author’s version of a work that was accepted for publication in Materials Science and Engineering. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality ...
Brauer, DS, Kobayashi, HYLS, Russel, C
core +1 more source
Molecular Oncology, EarlyView.Here, we demonstrate that HS1BP3 interacts with Cortactin through a proline‐rich region (PRR3.1) and show that this interaction, and HS1BP3 itself, promote cancer cell proliferation and invasion. Inhibition of this interaction leads to build‐up of TKS5 in multivesicular endosomes and altered secretion of CD63 and CD9, providing an explanation for the ...
Arja Arnesen Løchen +9 more
wiley +1 more source
The influence of drawing speed on surface topography of high carbon steel wires
Metalurgija, 2017 In this work the influence of the drawing speed on surface topography of high carbon steel wires has been assessed. The drawing process of f 5,5 mm wire rod to the final wire of f 1,7 mm was conducted in 12 passes by means of a modern Koch multi-die ...
M. Suliga
doaj
LubricantsThe wire drawing process, used for both ferrous and non-ferrous metals, employs different machines depending on the material and wire diameter: breakdown, single- or multi-wire machines for non-ferrous, and bull block machines for ferrous and non-ferrous
Juan Carlos del Rey +3 more
doaj +1 more source
Self-assembly of fine particle on three dimensional curved structure
Nihon Kikai Gakkai ronbunshu, 2014 Assembly of fine particles on three dimensional curved structure enables a lot of applications such as biochemical sensors. Dip coating method is often used because of its high productivity, but this method has been applied only to planar substrates. The
Manabu NISHIO, Nobuyuki MORONUKI
doaj +1 more source