Results 51 to 60 of about 2,647,604 (292)
FINITE ELEMENT ANALYSIS STUDY ON DEEP DRAWING SPEED PUNCH
Nonconventional Technologies Review, 2015 Analysis drawing process can sometimes be quite expensive and time consuming. Finite Element analysis manages to solve some of these shortcomings. It is very important that the results obtained by finite element simulation to be close to those obtained ...
Alin Pop, Ioan Radu, Florin Blaga
doaj
ComputationThe effective control of any technological process is essential in ensuring high-quality finished products. This is particularly true in manufacturing knowledge-intensive and high-tech products, including microstructured photonic crystal fibers (PCF ...
Daria Vladimirova +2 more
doaj +1 more source
FEBS Open Bio, EarlyView.We describe detailed protocols for the purification and preparation of Marchantia polymorpha Auxin Response Factor 2 (MpARF2). This protein is fused to an MBP solubility tag and an mNG fluorescent tag and is purified from Escherichia coli. The presented procedures make it possible to study MpARF2 assemblies, which could arise from phase separation ...
Bas Janssen +5 more
wiley +1 more source
Contracted site: Artist on paper, drawing [PDF]
, 2014 Traditionally the notion of drawing in-situ has suggested the physical presence of the artist in the environment under scrutiny. The assumption here of enhanced connectivity, however, is hasty in light of the idea that situation implies a relative ...
Jewell, Sharon Lee
core +1 more source
FEBS Open Bio, EarlyView.The two catalytic subunits of typhoid toxin dissociate from the holotoxin in the ER of an intoxicated cell, but only CdtB exits the ER to generate immunosuppressive effects. PltA is retained in the ER and sequestered from its cytosolic target, thus allowing the anti‐inflammatory effects of CdtB to promote intestinal colonization.
Maria C. Zabala‐Rodriguez +4 more
wiley +1 more source
FEBS Open Bio, EarlyView.Student engagement extends beyond simple attendance. Across 891 bioscience students from three universities, attendance behaviour was associated mainly with structural influences, whereas classroom spatial behaviour reflected affective and sensory factors.
Nigel Page +4 more
wiley +1 more source
Practice of Cold Drawing Process Optimization of GCr15 Bearing Steel Rod
Teshugang, 2015 The effect of draft, cone angle and length of sizing belt of drawing die, and drawing speed on drawing stress and drawing surface accuracy of bearing steel GCr15 (1. 01% C, 1. 58% Cr) Φ11 mm rod coil has been analyzed. The optimization process for Φ11 mm
王莹莹, 杨鹏远
doaj
Design and Simulation of Two-speed Variators with Large Transmission Ratio Based on the TRIZ Theory
Jixie chuandong, 2023 Aiming at the lack of speed variators with large transmission ratio for the chain cold drawing production line, on the basis of the ZSY500-50 three-stage reducer, the technical contradiction existing in the technical system is analyzed using the TRIZ ...
Du Chunkuan +3 more
doaj
Self-assembly of fine particle on three dimensional curved structure
Nihon Kikai Gakkai ronbunshu, 2014 Assembly of fine particles on three dimensional curved structure enables a lot of applications such as biochemical sensors. Dip coating method is often used because of its high productivity, but this method has been applied only to planar substrates. The
Manabu NISHIO, Nobuyuki MORONUKI
doaj +1 more source
, 1979 Od Vol. 43, issue 1 (1991) wyd.: Polish Scientific Publishers = PWN ; Od Vol. 50, issue 4 (1998) wyd.: Agencja Reklamowo-Wydawnicza A. Grzegorczyk ; Od Vol. 53, issue 4/5 (2001) wyd: PAS. IFTR ; 593-760 pages ; 24 cm ; Od Vol. 43, issue 1 (1991) wyd.: Polish Scientific Publishers = PWN ; Od Vol.
Camenschi, G., Cristescu, N., Sandru, N.
openaire +1 more source