Results 41 to 50 of about 7,150 (272)
Kinetic calculation analysis of Ga deposition on the morphology evolution of GaAs quantum ring
Materials Research Express, 2021 GaAs Quantum Ring (QR) was gained on GaAs (001) by Droplet Epitaxy (DE), and the microscopic morphology of the GaAs samples was observed by Scanning Tunnel Microscope (STM).
Qi-Zhi Lang +3 more
doaj +1 more source
MethodsX, 2019 Superhydrophobic surfaces (SHS) have potential in solving the icing of aircraft, high-voltage overhead transmission lines, and other power network devices exposed to the air.
H.Y. Zhang +5 more
doaj +1 more source
A Review on Fabrication and Application of Tunable Hybrid Micro–Nano Array Surfaces
Advanced Materials Interfaces, 2023 The wettability and adhesion of biological surfaces often depend on their periodically arranged hybrid micro–nano array structures. Various fabrication processes are designed to mimic biomimetic micro–nano array surfaces. This review summarizes the types
Chao Li +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Experimental and modelling investigation of the deformation, drag and break-up of drizzle droplets subjected to strong aerodynamics forces in relation to SLD aircraft icing [PDF]
, 2005 The distortion, drag and break-up of drizzle droplets subjected to strong aerodynamic forces was investigated to understand the pre-impact behaviour of droplets in aircraft icing from supercooled freezing drizzle.
Luxford, Geoffrey
core
Surface-dependent scenarios for dissolution-driven motion of growing droplets
Scientific Reports, 2017 Nano-droplets on a foreign substrate have received increasing attention because of their technological possible applications, for instance to catalyse the growth of nanowires.
Stefano Curiotto +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
The Investigation of Intermediate Stage of Template Etching with Metal Droplets by Wetting Angle Analysis on (001) GaAs Surface [PDF]
, 2010 In this work, we study metal droplets on a semiconductor surface that are the initial stage for both droplet epitaxy and local droplet etching. The distributions of droplet geometrical parameters such as height, radius and volume help to understand the ...
Yu G Galitsyn +11 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source