Results 11 to 20 of about 1,322,415 (284)
Dry rolling/sliding wear of nanostructured bainite [PDF]
Wear, 2014 Abstract The abrasive wear of carbide-free bainitic steel under dry rolling/sliding conditions has been studied. It is demonstrated that this nanostructure, generated by isothermal transformation at 200 °C, has a resistance to wear that supersedes that of other carbide-free bainitic steels transformed at higher temperatures.
S. Das Bakshi +3 more
openaire +2 more sources
Dry Sliding Wear Performance of ZA27/SiC/GraphiteComposites [PDF]
Metals, 2019 The paper describes the wear performance of zinc-aluminium ZA27 alloy, reinforced with silicon-carbide (SiC) and graphite (Gr) particles. The compo-casting technique produced the composite samples.
Nenad Miloradović +3 more
doaj +3 more sources
Sliding wear of nitrided steels [PDF]
, 1993 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.The unlubricated sliding wear behaviour of gas nitrided, plasma nitrided, and ferritic nitrocarburized BS970,905M39 (EN41B) steels was investigated ...
Kato, Hirotaka
core +7 more sources
Wear maps for TiC composite based coatings deposited on 303 stainless steel [PDF]
, 2014 Dry sliding wear (pin-on-disc) tests were carried out under ambient conditions at room temperature for TiC coated and uncoated 303 stainless steel, using alumina as a counterface.
Rasool, Ghulam +3 more
core +4 more sources
Journal of Magnesium and Alloys, 2017 The friction and wear behaviors of biodegradable Mg-6Gd-0.5Zn-0.4Zr (wt%, GZ60K) alloy were evaluated under simulated body fluid (SBF) condition using ball-on-disk configuration and compared with those under dry sliding condition.
Jianwei Dai +5 more
doaj +1 more source
EFFECT OF MAGNETIC FIELD ON FRICTION AND WEAR OF BRASS [PDF]
Journal of the Egyptian Society of Tribology, 2011 The present work discusses the effect of the magnetic field on the friction and wear of brass sheets scratched by a steel insert at dry and lubricated by vegetable oils and dispersed by polymeric particles such as polyethylene (PE), polyamide (PA6) and ...
A. E. Abeer +3 more
doaj +1 more source
Wear, 1996 The dry sliding wear behavior of the B2-structured (ordered body-centered cubic) compound NiAl has been studied. Pin-on-disk experiments were conducted at room temperature in air using pins made from extruded NiAl with compositions of 50, 48, and 45 at.% aluminum. Partially stabilized zirconia was the disk material.
B.J. Johnson, F.E. Kennedy, I. Baker
openaire +1 more source
Chemical and physical aspects of wear processes in polymers [PDF]
, 1972 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.A series of homogeneous halogen containing polymers have been studied whilst sliding against mild steel and oxides present on mild steel.
Richardson, MOW
core +7 more sources
Friction, 2018 The objective of this work is to investigate the influence of contact pressure and sliding speed on the coefficient of friction and wear of an activated carbon-epoxy composite derived from palm kernel under dry sliding conditions.
Dayang Nor Fatin Mahmud +4 more
doaj +1 more source
Studying the Dry Sliding Wear for Composite Material of Base (Al-4%Cu) Reinforcement by Silicon Carbide Particles [PDF]
Engineering and Technology Journal, 2014 This work is concerned with a study of dry sliding wear of Aluminum bace alloy of (Al-4%Cu) reinforcement by silicon carbide particles with different percentage (3, 6,9,12 wt %SiC).
Ahmad Ali Akbar Akbar +2 more
doaj +1 more source