Results 31 to 40 of about 1,322,415 (284)

Dry sliding wear of epoxy/cenosphere syntactic foams [PDF]

Tribology International, 2015
Dry sliding wear behavior of epoxy matrix syntactic foams filled with 20, 40 and 60 wt% fly ash cenosphere is reported based on response surface methodology. Empirical models are constructed and validated based on analysis of variance. Results show that syntactic foams have higher wear resistance than the matrix resin. Among the parameters studied, the
Vyasaraj Manakari, Gururaj Parande, Mrityunjay Doddamani, V.N. Gaitonde, I.G. Siddhalingeshwar, null Kishore, Vasanth Chakravarthy Shunmugasamy, Nikhil Gupta   +7 more
openaire   +2 more sources

Sliding wear of a-C:H coatings against alumina in corrosive media [PDF]

, 2013
This paper reports the results obtained from the study of friction and sliding wear in two corrosive solutions of an a-C:H coating deposited on 316L stainless against an alumina ball, employed as static counter part. Calculations of the values of the von
La Barbera Sosa, J.G., PUCHI-CABRERA, Eli-Saul, IOST, Alain, Santana Mendez, Y.Y., PUCHI-CABRERA, E.S., CHICOT, Didier, CHICOT, D., van Gorp, A., SANTANA, Y.Y., VAN GORP, Adrien, Carrasquero, E.J., Iost, A., STAIA, M.H., Puchi-Cabrera, Eli Saúl, CARRASQUERO, E., LA BARBERA-SOSA, J.G., Santana-Mendez, Y.Y.   +16 more
core   +1 more source

Avidin is evolutionarily conserved in fish but dispensable for development and resistance against Streptococcus agalactiae in zebrafish

FEBS Open Bio, EarlyView.
The presence of biotin‐binding avidin proteins in fish and their biological significance are poorly characterized. We cataloged fish avidins and demonstrate that they are widely present and evolutionarily conserved. We created avd knockout zebrafish and show that zebavidin is dispensable for development and that resistance of avd knockout embryos in ...
Anni K. Saralahti, Markus J. T. Ojanen, Mataleena Parikka, Otto Kauko, Mika Rämet, Vesa P. Hytönen   +5 more
wiley   +1 more source

Low‐Temperature Imidization of Polyimides (PI) for Scalable Manufacturing of Flexible Wearable Electronics

Advanced Engineering Materials, EarlyView.
Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley   +1 more source

Tribological characteristics of compacted graphite cast iron in dry sliding condition [PDF]

China Foundry, 2006
The dry sliding wear and friction behaviors of compacted graphite cast iron (C. G. iron) were analyzed. The influence of the operating conditions (i.e.
CHEN Yue, ZHANG Yong-zhen, ZHANG Ran-yang   +2 more
doaj  

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Prediction of Sliding Wear of Artificial Rough Surfaces [PDF]

, 2012
When two surfaces are brought in contact, deformation takes place at asperity level. The local pressure distribution and deformation of the contacting surfaces are importance with respect to wear.
Imam , Syafa’at, D.J., Schipper, J. , Jamari, Rifky , Ismail, Budi , Setiyana, Eko , Saputra   +5 more
core   +1 more source

Comparative study on dry sliding wear behavior of mono (Al2219/B4C) and hybrid (Al2219/B4C/Gr) metal matrix composites using statistical technique

Journal of the Mechanical Behavior of Materials, 2020
In the present study, aluminium metal matrix composites (AMMC’s) reinforced with boron carbide (B4C) and graphite (Gr) particles were prepared by stir casting method.
Suresh R.
doaj   +1 more source

Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles

Advanced Engineering Materials, EarlyView.
Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan, Johannes Wendler, Dilbar Aibibu, Johannes Mersch, Michael Wöltje, Chokri Cherif   +5 more
wiley   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source