APPLICATION OF TAGUCHI TECHNIQUES TO STUDY DRY SLIDING WEAR BEHAVIOUR OF MAGNESIUM MATRIX COMPOSITES REINFORCED WITH ALUMINA NANO PARTICLES [PDF]
Journal of Engineering Science and Technology, 2017 Magnesium metal matrix composites reinforced with alumina Nano particles are prepared by liquid metallurgy route. Dry sliding wear behavior of the composite was tested and compared with AZ91 magnesium alloy.
TARASASANKA C., RAVINDRA K.
doaj
TEM characterisation of near surface deformation resulting from lubricated sliding wear of aluminium alloy and composites [PDF]
, 2007 Aluminium alloy composites have been extensively investigated for use in tribo-contact applications, however little detailed literature exists on the sub-surface microstructural evolution as a result of lubricated sliding wear.
Rainforth, W.M. +7 more
core +1 more source
Diyala Journal of Engineering Sciences, 2013 This research is devoted to study the effect of addition of different weight percent from SiCp ( 2, 4, 6, 8 ) to Al– 4 Cu alloy which have been fabricated by liquid metallurgy method on the dry sliding wear behavior and mechanical properties.
Israa .A.K
doaj +1 more source
TRIBOLOGICAL BEHAVIOURS OF ABS AND PA6 POLYMERMETAL SLIDING COMBINATIONS UNDER DRY FRICTION, WATER ABSORBED AND ELECTROPLATED CONDITIONS [PDF]
Journal of Engineering Science and Technology, 2016 The friction and wear properties of polyamide 6 (PA6) and poly-Acrylonitrile Butadiene Styrene (ABS) sliding against metal under dry sliding, water absorption and electroplated (EP) conditions were studied by using a pin-ondisc tribometer.
MITHUN V. KULKARNI +3 more
doaj
Dry sliding wear characteristics of aluminium metal matrix composites: a brief overview
Journal of Materials Research and Technology, 2019 Aluminium composites with reinforcements in the form of whiskers, particulates or continuous/discontinuous fibres are referred to as aluminium metal matrix composites (Al MMCs).
Nosa Idusuyi, John I. Olayinka
doaj +1 more source
The Effect of Iron Addition on the Dry Sliding Wear and Corrosion Behavior of Cu Al Ni Shape Memory Alloy [PDF]
Engineering and Technology Journal, 2010 In this paper, dry sliding wear and corrosion behavior of Cu + 13wt% Al + 3.8 wt% Ni was prepared by powder metallurgy. Dry sliding wear has been studied based on pin on disk at constant velocity and constant sliding distance .Corrosion behavior in 5 wt%
Abdul Raheem . K. Abid Ali +1 more
doaj +1 more source
Journal of Natural Fibers, 2022 This paper reports on the dry-sliding wear behavior of natural fiber fortified polymer composites. Such composites are fabricated using epoxy as the matrix and short areca-catechu fibers as the reinforcing element through the conventional hand lay-up ...
Purushottam Kumar Choudhary +2 more
doaj +1 more source
Impact-Sliding of Sintered Steel: Effect of Lubrication
Tribology Online, 2013 Sintered steel is used as a material for valve seat insert in automotive engines. During operation, a dynamic contact occurs between the valve and its seat.
Maha Messaadi +2 more
doaj +1 more source
Surface morphology in engineering applications: Influence of roughness on sliding and wear in dry fretting [PDF]
, 2011 Influence of initial surface roughness on friction and wear processes under fretting conditions was investigated experimentally. Rough surfaces (Ra=0.15-2.52 [mu]m) were prepared on two materials: carbon alloy (AISI 1034) and titanium alloy (Ti-6Al-4V ...
Mathia, T.G. +8 more
core +1 more source
Wear Behavior of Woven Roving Aramid / Epoxy Composite under Different Conditions
International Islamic University Malaysia Engineering Journal, 2012 Wear behavior studies of aramid woven roving /epoxy composite has been conducted. Sliding the material against smooth steel counter face under dry and lubricated with oil conditions has been investigated.
Asad A. Khalid
doaj +1 more source