Results 81 to 90 of about 428,090 (297)

Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann, Berend Denkena, Hilke Petersen, Florian Schaper   +3 more
wiley   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source

Effect of strain on the interlayer friction behavior of double- walled carbon nanotubes with abnormal interlayer distances

Xi'an Gongcheng Daxue xuebao
In order to reveal the friction mechanism of low-dimensional nanomaterials, and effectively regulate the friction process, the interlayer friction of coaxial double-walled carbon nanotubes (DWNTs) with different interlayer distances under axial tension ...
ZHANG Hongwei, GUO Zhongjun
doaj   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Dynamic Friction Behavior of Paper-Based Wet Friction Material Subjected to Contact Pressure Fluctuation

Tribology Online, 2012
In this research, dynamic friction behavior of paper-based wet friction material subjected to contact pressure fluctuation was investigated experimentally and theoretically. Complex friction coefficient obtained by the ratio between dynamic components of
Yasuhisa Hattori, Yusuke Kato
doaj   +1 more source

Simulation of the Burridge-Knopoff Model of Earthquakes with Variable Range Stress Transfer

, 2006
Simple models of earthquake faults are important for understanding the mechanisms for their observed behavior, such as Gutenberg-Richter scaling and the relation between large and small events, which is the basis for various forecasting methods. Although
C. Scholz, Harvey Gould, J. B. Rundle, Junchao Xia, R. Burridge, W. Klein   +5 more
core   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

A novel method to establish friction coefficient model for numerical simulation of inertia friction welding

Materials & Design
The precise friction coefficient at interface determines the friction behavior in inertia friction welding (IFW), its model is the basis to precisely describe the friction behavior in the numerical simulation of IFW.
Hao Wang, Guoliang Qin, Banglong Fu, Yuan Gao, Changan Li   +4 more
doaj   +1 more source

A 2-D asymmetric exclusion model for granular flows

, 1999
A 2-D version of the asymmetric exclusion model for granular sheared flows is presented. The velocity profile exhibits two qualitatively different behaviors, dependent on control parameters.
C Josserand, Debregeas G., Derrida B., Mueth D. M., Rajchenbach J., Veje C.   +5 more
core   +3 more sources