Results 71 to 80 of about 17,765 (271)
Journal of Quaternary Science, EarlyView.ABSTRACT The Aso‐3 tephra is one of the most significant widespread marker layers from the Middle to Late Pleistocene, generated by a large caldera‐forming eruption at the Aso volcano in Kyushu, southwestern Japan. Despite its importance, a distal co‐ignimbrite ash correlative has yet to be clearly identified, primarily because although volcanic glass ...
Toshinori Sasaki +6 more
wiley +1 more source
Macromolecular Rapid Communications, EarlyView.Liquid crystal elastomer (LCE) filaments are fabricated through extrusion with in‐process UV curing, enabling controlled flow alignment and network locking of mesogens. The resulting structure responds to thermal or optical stimuli, inducing molecular reorientation and macroscopic contraction.
Anne Schwarz‐Pfeiffer, Shazia Mehtab
wiley +1 more source
, 2013 Friction Stir Welding (FSW) is a complex thermal-mechanical process. Numerical models have been used to calculate the thermal field, distortion and residual stress in welded components but some modeling parameters such as film coefficient and thermal ...
Pan, Wenke +2 more
core +1 more source
Materials Genome Engineering Advances, EarlyView.Four constitutive models are evaluated for FeCoNiCr and Al0.6FeCoNiCr HEAs under wide temperature and strain‐rate conditions. The predictive capabilities and limitations of each model are then critically assessed, with particular emphasis on strain rate sensitivity, temperature dependence, and physically unrealistic responses at extreme loading ...
Yooseob Song +3 more
wiley +1 more source
Optimal workplacement for robotic friction stir welding task
, 2013 Robotic manipulators are widely used in industry for welding processes. Inadequate joint stiffness in the manipulators often limits their use for high quality welding operations because of the deformation errors produced during the process.
ABBA, Gabriel, QIN, Jinna, JAIN, Achin
core
Material constitutive behaviour and microstructure study on aluminium alloys for friction stir welding [PDF]
, 2010 The material constitutive behaviour and microstructure of Aluminium alloys 6082 and 7449 were studied with the Gleeble hot compression test. The novel aspect of the work is that the testing was done at high strain-rates and at temperatures within 5 K ...
Colegrove, Paul A. +4 more
core +1 more source
Polymer Composites, EarlyView.Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia +4 more
wiley +1 more source
Multi-response optimization of CO2 laser welding process of austenitic stainless steel [PDF]
, 2008 Recently, laser welding of austenitic stainless steel has received great attention in industry, due to its wide spread application in petroleum refinement stations, power plant, pharmaceutical industry and households.
Olabi, Abdul-Ghani +2 more
core +1 more source
Polymer International, EarlyView.An overview and categorization of man‐made per‐ or polyfluoroalkyl substances (PFASs) including low‐molar‐mass and high‐molar‐mass fluorochemicals, and their international regulations is presented. Though certain PFASs are toxic, bioaccumulative and cross the human cellular membranes, others, such as fluoropolymers, are safe, reliable and involved in ...
Bruno Améduri
wiley +1 more source
Analysis Method of Friction Torque and Weld Interface Temperature during Friction Process of Steel Friction Welding [PDF]
, 2010 This paper describes an analysis method of the friction torque and weld interface temperature during the friction process for steel friction welding. The joining mechanism model of the friction welding for the wear and seizure stages was constructed from
KAIZU, Koichi +4 more
core +1 more source