Results 41 to 50 of about 160,405 (309)

Preparation of feedstock for potassium chloride granulation plants

open access: yesВесці Нацыянальнай акадэміі навук Беларусі: Серыя фізіка-тэхнічных навук
The assessment of existing technological solutions in the field of preparation of feedstock for potassium chloride granulation plants of silvinite processing plants of JSC “Belaruskali”, compliance of these solutions with the developed theoretical ...
O. M. Volchek, V. Ya. Prushak
doaj   +1 more source

Time scale analysis for fluidized bed melt granulation I: Granule–granule and granule–droplet collision rates [PDF]

open access: yesChemical Engineering Science, 2011
Fluidized bed spray granulators (FBMG) are widely used in the process industry for particle size growth; a desirable feature in many products, such as granulated food and medical tablets. In this paper, the first in a series of four discussing the rate of various microscopic events occurring in FBMG, theoretical analysis coupled with CFD simulations ...
Chua, Kel W.   +2 more
openaire   +1 more source

Functional and Structural Evidence of Neurofluid Circuit Aberrations in Huntington Disease

open access: yesAnnals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective Disrupted neurofluid regulation may contribute to neurodegeneration in Huntington disease (HD). Because neurofluid pathways influence waste clearance, inflammation, and the distribution of central nervous system (CNS)–delivered therapeutics, understanding their dysfunction is increasingly important as targeted treatments emerge.
Kilian Hett   +8 more
wiley   +1 more source

THE STUDY OF THE KINETIC OF NATURAL ZEOLITE GRANULES GROWTH AT DIFFERENT WAYS OF GRANULATION [PDF]

open access: yesAnnals of Mechnikov's Institute, 2016
Introduction. Active substances and excipients used in the manufacture of medicines in tablet form, in most cases, have poor technological properties. This fact determines the need for prior granulation of mass before compression.
Rybachuk VD
doaj   +1 more source

Temporal variations in the acoustic signal from faculae

open access: yes, 2012
The integrated brightness of the Sun shows variability on time-scales from minutes to decades. This variability is mainly caused by pressure mode oscillations, by granulation and by dark spots and bright faculae on the surface of the Sun.
Aigrain   +37 more
core   +1 more source

Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula   +7 more
wiley   +1 more source

Rapid Nondestructive Detection of Water Content and Granulation in Postharvest “Shatian” Pomelo Using Visible/Near-Infrared Spectroscopy

open access: yesBiosensors, 2020
Visible/near-infrared (VIS/NIR) spectroscopy is a powerful tool for rapid, nondestructive fruit quality detection. This technology has been widely applied for quality detection of small, thin-peeled fruit, though less so for large, thick-peeled fruit due
Sai Xu   +4 more
doaj   +1 more source

Wet granulation in laboratory scale high shear mixers: Effect of binder properties [PDF]

open access: yes, 2011
The effect of binder properties on torque curves, granule growth kinetics, wet mass consistency and dry granule strength has been investigated in this study.
Chitu, Toma Mihai   +2 more
core   +3 more sources

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

open access: yesAdvanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost   +4 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Home - About - Disclaimer - Privacy