Results 41 to 50 of about 46,069 (286)
Control of Fungal Diseases in Mushroom Crops while Dealing with Fungicide Resistance: A Review
Microorganisms, 2021 Mycoparasites cause heavy losses in commercial mushroom farms worldwide. The negative impact of fungal diseases such as dry bubble (Lecanicillium fungicola), cobweb (Cladobotryum spp.), wet bubble (Mycogone perniciosa), and green mold (Trichoderma spp ...
Francisco J. Gea +4 more
doaj +1 more source
Enhancing the Fatigue Strength of the Weld Line in Advanced Polymer Injection Molding: Gas-Assisted Mold Temperature Control for Thermoplastic Polyurethane (TPU) Composites [PDF]
, 2023 This study presents an innovative approach to enhancing weld line strength in advanced polymer injection molding through applying gas-assisted mold temperature control, significantly increasing mold temperature beyond typical values observed in ...
Thanh Trung Do +4 more
core +1 more source
Extracts of Ulva lactuca Induce Responses against Penicillium digitatum on Oranges
Phycology, 2023 Penicillium digitatum causes severe damage to postharvest and stored citrus fruits, making it necessary to seek acceptable solutions limiting environmental and sanitary impacts.
Douaa Salim +4 more
doaj +1 more source
Foods, 2021 Penicillium digitatum is the main postharvest pathogen of citrus fruit. Although the inner fruit peel part (albedo) is less resistant than the outer part (flavedo) to P.
María Teresa Lafuente +2 more
doaj +1 more source
Journal of Fungi, 2022 In this study, a γ-cyclodextrin-cinnamaldehyde inclusion compound (γ-CDCL) was prepared to control green mold caused by Penicillium digitatum (P. digitatum) in citrus.
Yonghua Zhang +4 more
doaj +1 more source
Calculating Methods on Remained Measure of Repairing Mold in Green Product Design [PDF]
, 2010 This article primarily analyzes the shortcoming in the current formula of plastic and rubber mold shaped dimensions in practical， and fully considered the influence of plastic and rubber contracting fluctuation ratio on the accuracy of the plastic and ...
Jun An Liu +4 more
core +1 more source
Incidence of Toxigenic and Other Molds in Green Coffee Beans
Journal of Food Protection, 1983 The mold flora of 944 green coffee bean samples from 31 coffee-producing countries was determined before and after surface disinfection with 5% NaOCl. Molds were detected on 99.1 % of 47,200 beans not surface-disinfected and in 47.9% of 47,200 disinfected beans.
Philip B, Mislivec +2 more
openaire +2 more sources
RANCANG BANGUN CETAKAN PEMANEN (PERMANENT MOLD) UNTUK PEMBUATAN PULLEY ALUMINIUM [PDF]
, 2010 Many efforts have been done to increase efficiencies and margin (without ignoring the quality) in casting industry. Most of the producer of non-ferrous pulleys in South Sumatra region are handled by small and medium scale industries using simple ...
Firdaus, Firdaus
core +4 more sources
Open CeramicsCeramic injection molding is a net-shape manufacturing process to mass-produce ceramic components. During demolding adhesive forces act between the ejected green body and the mold surface.
Jonas Veit +3 more
doaj +1 more source
Control of Citrus Green Mold by Carbonate and Bicarbonate Salts and the Influence of Commercial Postharvest Practices on Their Efficacy [PDF]
, 1999 The toxicity to Penicillium digitatum and practical use of carbonate and bicarbonate salts to control green mold were determined. The effective dose (ED50) concentrations to inhibit the germination of P.
Mlikota, Franka +4 more
core +1 more source