Results 41 to 50 of about 36,806 (247)
Journal of Materials Research and TechnologyPre-deformation is a cost-efficient method to control the microstructure and mechanical properties of wrought magnesium (Mg) alloys. It introduces twins that promote dynamic recrystallization during hot deformation, thereby improving hot workability and ...
Junsong Jin +10 more
doaj +1 more source
Deformation behavior of a new Ni-Co base superalloy GH4251 during hot compression
Materials Research Express, 2023 The deformation behavior of a new Ni-Co base superalloy GH4251 under hot compression tests within the deformation strain window of 0.36 to 1.2 was investigated in the temperature range of 1050 ∼ 1170 °C and strain rate range of 0.001 ∼ 1 s ^−1 . Based on
Hongyao Yu +6 more
doaj +1 more source
Hot Deformation Behavior of PM Ni with Harmonic Microstructure
Metals, 2022 The hot deformation behavior of a harmonic-structured pure nickel has been studied and compared with the hot deformability of a homogeneously structured nickel.
Cinzia Menapace +2 more
doaj +1 more source
Journal of Materials Research and Technology, 2021 7055 aluminum alloy was produced by twin-roll casting (TRC) and by conventional mold casting (MC). Homogenization at 465 °C for 24 h with natural cooling was applied, followed by uniaxial hot compression tests to verify the hot workability of the alloy ...
Xiaoming Qian +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Excellent combinations of strength and impact toughness are obtained in a bilayer composite of high‐strength carbide‐free bainitic (CFB) steel and high‐ductility twinning‐induced plasticity (TWIP) steel. The composite absorbs energy at small strains when the notch is placed on the TWIP side and at high strains when the notch is placed on the CFB side ...
Kendra Hawke +5 more
wiley +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Recent Progress in Oxide‐Based Na‐Ion Conductors
Advanced Engineering Materials, EarlyView.Recent advances in oxide‐based sodium‐ion conductors are reviewed, focusing on β/β″‐alumina, NASICON‐type compounds, and Na5YSi4O12‐type (N5) silicates, together with emerging perovskite and layered oxides. Improvements in ionic conductivity, compositional tuning, and processing are highlighted.
Bowei Xun +3 more
wiley +1 more source
Enhanced creep resistance in Mg-Y-Nd alloy via regulating prior thermo-mechanical treatment
Journal of Magnesium and AlloysIn this study, the tensile creep behavior of a hot-rolled Mg-4Y-3.5Nd alloy subjected to different prior thermo-mechanical treatments was investigated at 220 ℃.
Zhirou Zhang +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh +3 more
wiley +1 more source
Metals, 2016 Hot deformation behavior and microstructure evolution of 2707 hyper duplex stainless steel (HDSS) were investigated through hot compression tests in the temperature range of 900–1250 °C and strain rate range of 0.01–10 s−1.
Huabing Li +8 more
doaj +1 more source