Results 51 to 60 of about 38,287 (265)

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Investigation on the microstructure and mechanical properties of large-tube forging manufactured by additive forging

Materials Research Express
Large-tube forgings were formed using nine layers of continuous-casting billet made from 15CrNi3MoV alloy steel via additive forging. The interfacial microstructural evolution under different hot-compression bonding temperatures and strains was ...
Bing Wang, Hong-Lin Zhang, Bin Xu, Ming-Yue Sun, Dian-Zhong Li   +4 more
doaj   +1 more source

Permanent Densification of Calcium Aluminophosphate Glasses

Frontiers in Materials, 2019
High-temperature densification of oxide glasses influences their interatomic distances and bonding patterns, resulting in changes in the mechanical and chemical properties.
Saurabh Kapoor, Randall E. Youngman, Lina Ma, Nadja Lönnroth, Sylwester J. Rzoska, Michal Bockowski, Lars R. Jensen, Mathieu Bauchy, Morten M. Smedskjaer   +8 more
doaj   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

Hot compression behavior, simulation verification and dynamic recrystallization mechanism of Mg-Gd-Y-Zr alloy

Journal of Materials Research and Technology
The uniaxial hot compression experiments of Mg-7Gd-3Y-0.5Zr (VW73K) alloy were carried out by using the Instron5982 mechanical testing machine with environmental box. The hot deformation behavior at 350–500 °C and 0.001–1 s−1 was studied.
Dongzhen Wang, Xiaoya Chen, Quanan Li, Hongxi Zhu, Huanju He   +4 more
doaj   +1 more source

Hot sterilized compressed air—an electrical apparatus for heating and sterilizing compressed air [PDF]

The Laryngoscope, 1898
n ...
openaire   +2 more sources