Results 231 to 240 of about 46,916 (258)

Grease effect on fretting wear of mild steel

Industrial Lubrication and Tribology, 2008
Purpose – The aim of this paper is to research grease and additives' influence on fretting wear of mild steel.Design/methodology/approach – Experiments were performed on a laboratory stand with contact conditions cylinder on flat. The mild steel couples were tested under dry conditions and lubricated with mineral and synthetic greases containing as ...
Antoni Neyman, Jan Sikora
openaire   +1 more source

Tire Wear Caused by Mild Tread Slip

Rubber Chemistry and Technology, 1997
Abstract The purpose of this study is to examine the relationship between the tread wear of rolling tires and the wear of a sliding rubber pad. In the experiments, frictional parameters, i.e. sliding distances, sliding velocities, and contact pressures, are evaluated at points on the tire-tread surface.
Tatsuo Fujikawa, Shunichi Yamazaki, Yoshitaka Uchiyama   +2 more
openaire   +1 more source

The unlubricated fretting wear of mild steel in air

Wear, 1985
Abstract Fretting experiments were carried out on mild steel in air to long sliding distances over a range of loads and stroke amplitudes. For peak-to-peak fretting amplitudes greater than 5 μm, three fretting stages were identified: an initial adhesive transfer stage, an intermediate stage where both metallic and oxide debris were produced and a ...
D. Aldham, J. Warburton, R.E. Pendlebury
openaire   +1 more source

Reaction products in and around the wear track in the lubricated mild wear regime

Wear, 1984
Abstract Liquid or solid reaction products that are insoluble in the lubricant and the metallic wear debris generated in the wear track are partially deposited around the wear track where they can be easily studied after experiments. A ball-on-plate friction apparatus operating in the mild wear regime is used for investigating these deposits and the ...
openaire   +1 more source

Wear resistance of plasma coatings on mild steel

Journal of Materials Science, 1991
Mild steel was coated by different materials using plasma spray technique. Materials used as coatings are Ni-5% Al and WC-17% Co. The thickness of the coatings varied between 0.05 to 1.5 mm. The porosity of different coatings decreased with increase in thickness of the coat. The roughness of coating material decreased after wear testing. Microstrueture
M. M. I. Ahmed, R. A. Abd EL-Karim, S. M. El-Raghy, F. A. El-Refaie, A. E. El-Mehairy   +4 more
openaire   +1 more source

Mild microscopic wear in the boundary lubrication regime

Materialwissenschaft und Werkstofftechnik, 2010
AbstractThe transition from a mild wear situation to a severe (adhesive) wear situation is of great interest to be able to design highly loaded concentrated contacts operating in the boundary lubricated regime. In this article a method is described to estimate this transition, based on a thermal criterion.
openaire   +2 more sources

An experimental analysis of a mild wear process

2013
U.S. Navy (U.S.N.) authors.
Barrett, Roy Franklin, Gildea, Joseph Alroy   +1 more
openaire   +1 more source

Some microscopic aspects of the mild wear of steel*

Journal of Microscopy, 1971
SUMMARYThe paper reviews the experimental classifications of the unlubricated sliding wear of metals, together with some of the suggested relationships between the wear rates, the real area of contact, the load, the hardnesses of the metals and the probability of producing wear particles at the real areas of contact.
openaire   +1 more source

Relation of normal load with test temperature at mild–severe wear transition state for Mg–Gd–Y–Zr alloy

Transactions of Nonferrous Metals Society of China, 2021
Jian An
exaly  

A study of some aspects of a mild wear process

2012
http://archive.org/details ...
Boyd, John Huntly., Charbonneau, George Lee., Kaetzel, David Murray.   +2 more
openaire   +1 more source