Results 51 to 60 of about 46,735 (198)

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

What Do Large Language Models Know About Materials?

Advanced Engineering Materials, EarlyView.
If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer, Thomas Wallmersperger, Gianaurelio Cuniberti   +2 more
wiley   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects

Advanced Engineering Materials, EarlyView.
Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini, Lu Fang, Jacob Bons, Mohammad Humaun Kabir, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Comparative safety of intravenous Ferumoxytol versus Ferric Carboxymaltose for the Treatment of Iron Deficiency Anemia: rationale and study design of a randomized double-blind study with a focus on acute hypersensitivity reactions

Journal of Blood Medicine, 2017
N Franklin Adkinson,1 William E Strauss,2 Kristine Bernard,2 Robert F Kaper,2 Iain C Macdougall,3 Julie S Krop2 1Department of Medicine, Division of Allergy and Clinical Immunology, Johns Hopkins University School of Medicine, Baltimore, MD, USA; 2AMAG ...
Adkinson NF, Strauss WE, Bernard K, Kaper RF, Macdougall IC, Krop JS   +5 more
doaj  

A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions

Advanced Engineering Materials, EarlyView.
This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice, Krzysztof S. Stopka, Michael D. Sangid   +2 more
wiley   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source