Results 201 to 210 of about 878,159 (309)

Accelerated Degradation of PLA‐Based Composites in Harsh Alkaline Environment

Polymer Composites, EarlyView.
Evolution of surface properties and features of RP sample treated in harsh conditions: FTIR and wetting analysis. ABSTRACT The performance of poly(lactic acid) (PLA) bioplastics under harsh service conditions must be understood to enable their use in multi‐use products.
Cristina Moliner, Alberto Lagazzo, Juan Felipe Basbus, Roberto Raiteri, Elisabetta Finocchio, Elisabetta Arato   +5 more
wiley   +1 more source

Low power and high-speed quadrate node upset tolerant latch design using CNTFET. [PDF]

Sci Rep
Asiya S, S SK.
europepmc   +1 more source

Masterbatch‐Assisted Fabrication of Polylactic Acid/Reduced Graphene Oxide Nanocomposites Exhibiting Mechanical Enhancement and UV‐C Aging Resistance

Polymer Composites, EarlyView.
Masterbatch‐Assisted Fabrication of Polylactic Acid/Reduced Graphene Oxide Nanocomposites. ABSTRACT Polylactic acid (PLA) is a promising bio‐based polymer; nonetheless, its extensive application is still limited by poor fracture toughness, low thermal stability, and strong susceptibility to degradation induced by ultraviolet (UV) radiation.
Maria Giovanna Pastore Carbone, Nikolaos Koutroumanis, George Paterakis, Julio Gomez, Costas Galiotis   +4 more
wiley   +1 more source

Corner Simulation of CMOS Analog Integrated Circuit Taking into Account Radiation Influence. [PDF]

Micromachines (Basel)
Ryzhov S, Kuznetsov V, Andreev V.
europepmc   +1 more source

Low‐Velocity Impact Response and Damage Mechanisms of 3D Printed ASA‐Glass Fiber Composites

Polymer Composites, EarlyView.
ASA + GF 3D‐printed specimens: fabrication, impact test and anisotropic fracture under 0/90° and 45/−45° print orientations. ABSTRACT This study investigates the low velocity impact behavior and underlying damage mechanisms of 3D printed acrylonitrile styrene acrylate reinforced with short glass fibers (ASA + GF) composites.
Sachini Wickramasinghe, Janitha Jeewantha, Allan Manalo   +2 more
wiley   +1 more source

New beam hardened data correction and its application to artifact reduction in CT images. [PDF]

Med Phys
Kim S, Kim SH, Song MK, Shin J, Seo JH, Kang JY.   +5 more
europepmc   +1 more source

Evaluation of Graphene Oxide–Modified Repair Methodologies in Carbon Fiber Reinforced Polymer Composites for Aerospace Applications

Polymer Composites, EarlyView.
Schema 1. Schematic representation of the graphene oxide (GO)‐modified wet lay‐up repair strategy for CFRP laminates, illustrating stepwise ply removal, incorporation of GO into the epoxy repair matrix, and the enhanced mechanical performance of the repaired laminate.
Togay Yildirim, Tugba Soganci Aras
wiley   +1 more source

Computational and Experimental Modeling of Interfaces and Joints in Advanced Materials. [PDF]

Materials (Basel)
Grzejda R.
europepmc   +1 more source

Recycled Polyacrylonitrile Nanofiber Interleaves With Graphene Nanoplatelets for Adhesively Bonded Composite Joints: Lap‐Shear and Opening‐Mode Fracture Performance

Polymer Composites, EarlyView.
Textile‐waste Orlon is transformed into recycled PAN nanofiber interleaves for tougher and more damage‐resistant adhesive bondlines. ABSTRACT This study presents a sustainable toughening strategy for adhesively bonded CFRP joints by using electrospun polyacrylonitrile (PAN) nanofiber interleaves produced from virgin PAN (vPAN) and recycled PAN (rPAN ...
Mehmet Emin Çetin, Asım Üstün, Mehmet Okan Erdal, Hasan Ulus   +3 more
wiley   +1 more source

Performance of Coating Mortars with Partial Replacement of Natural Aggregate by Açaí Seed Residual Ash from the Amazon Region. [PDF]

ACS Omega
de Almeida BL, Paes INL, Cordeiro LNP.
europepmc   +1 more source