Results 31 to 40 of about 890,044 (188)
Mechanical Analysis of a Scraping Method to Remove Attached Barnacles
Journal of Marine Science and Engineering, 2020 In order to clean the marine fouling attached to marine steel piles, a scraping method is proposed in this paper. Barnacles were used to represent a typical object needing removal, in order to estimate the maximum force required in the equipment designed
Chao Li +4 more
doaj +1 more source
Experiments in the Machining of Ice at Negative Rake Angles
Journal of Glaciology, 1984 AbstractThe cutting force components and the cutting moment on the cutting tool were measured during the orthogonal machining of ice with cutting tools inclined at negative rake angles. The variables included the cutting depth (< 1 mm), the cutting speed (0.01 ms−1 to 1 ms−1), and the rake angles (–15° to –60°).
D.K. Lieu, C.D. Mote
openaire +1 more source
Design front rake angle of PDC bit based on SolidWorks simulation method [PDF]
, 2016 In order to solve the bit front rake angle parameter selection problem of under different coal rock, it is proposed in polycrystalline diamond compact no core bit as the research object, and established a bit compact two-dimensional stress model of ...
HAN, Xiaoming, LUO, Chenxu, HAN, Xingyu
core +1 more source
Rake angle effect in cutting-based single atomic layer removal [PDF]
, 2020 When minimum cutting depth is down to a single atomic layer, two portions of the cutting tool, namely, cutting edge and lowest atoms of the cutting tool, are involved in the cutting-induced material removal.
Fang, Fengzhou, Xie, Wenkun
core +2 more sources
JUSTIFICATION OF RAKE ANGLE PARAMETERS REGARDING MOVEMENT AND RAKING OF HAY WITH ROTARY RAKES
Vibrations in engineering and technologyIn modern conditions of agricultural production, improving the efficiency of hay harvesting technologies is an important task for ensuring quality fodder for livestock. One of the key elements in this process is the use of rotary rakes to move and rake the hay. The efficiency of these machines largely depends on the design parameters, in particular the
Yuriy Paladiychuk, Pavlo Stetsyuk
openaire +1 more source
Blind space-time RAKE structure based on second order statistics for DS-CDMA [PDF]
, 2001 This paper presents a new algorithm that ensures low complexity implementation of a blind ST Rake receiver for DS-CDMA. The algorithm is applicable for both periodic and non-periodic spreading sequences provided that the system utilizes two layers of ...
Piechocki, RJ +2 more
core +1 more source
Applied SciencesThe cutting temperature in hard turning is extremely high, which reduces tool life, lowers machined-surface quality, and affects dimensional control.
Pham Minh Duc +2 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 Laser assistance and the use of a diamond tool with a negative rake angle are promising methods for machining hard and brittle materials. In this paper, a cutting force model and a smoothed particle hydrodynamics (SPH) model were constructed to ...
Chuangting Lin +7 more
doaj +1 more source
Design method and parameter optimization of small angle rake face of hourglass worm gear hob
Journal of Advanced Mechanical Design, Systems, and ManufacturingIn order to improve the cutting performance of the hourglass worm gear hob and improve the cutting conditions of the teeth on both sides, it is necessary to constrain the absolute value of the rake angle of each tooth to be small and control the balance ...
Kang ZHAO +4 more
doaj +1 more source
Journal of Manufacturing and Materials ProcessingThis study investigates the effects of the rake angle and clearance angle of custom-manufactured HSS-E Co5 high-speed steel cutting tools on the Fc main cutting force, the Fp passive force component, the Ra and Rz surface roughness parameters, and chip ...
Norbert Szabó, Gábor Kónya
doaj +1 more source