Dry sliding wear behavior of SiC-reinforced Al-Si eutectic metal matrix composite [PDF]
Scientific ReportsThis study investigates the effect of sliding parameters on the dry sliding wear behavior of (silicon carbide) SiC-reinforced (aluminum silicon) Al-Si eutectic metal matrix composites (MMCs) with 1.5 wt% of magnesium (Mg).
Ashwin Shetty +4 more
doaj +2 more sources
Development of a novel cycling impact–sliding wear rig to investigate the complex friction motion
Friction, 2017 In many industrial devices, impact-sliding wear is caused by a variety of complex vibrations between the contacted interfaces. Under actual conditions, impact and sliding motions do not occur in only one direction, and different complex impact-sliding ...
Zhenbing Cai +5 more
doaj +3 more sources
A Study on Tribological Behaviour of Electro Discharge Deposited ZE41A Magnesium Alloy Using Wear Map [PDF]
Archives of Metallurgy and Materials, 2021 The paper studied the tribological behaviour of electro discharge deposited ZE41A magnesium alloy using wear map. The wear experiments are conducted using pin on disc technique for different parameters such as applied load (1.5 kg-3.5 kg), sliding speed (
U. Elaiyarasan +2 more
doaj +1 more source
Influence of Applied Load and Sliding Distance on Wear Performance of AlSi7Mg0.6 Aluminum Alloy
Metals, 2023 The wear performance of AlSi7Mg0.6 aluminum alloy, a casting aluminum alloy used in positioning devices for catenary systems of high-speed railways which fail frequently on lines where the speed of trains is higher than 300 m/s, is discussed in this ...
Haibo Zhang +3 more
doaj +1 more source
An investigation on dry sliding wear behavior of Al6061/ Titanium carbide/ Basalt hybrid metal matrix composites [PDF]
INCAS Bulletin, 2021 Dry sliding wear plays an important role in selecting material for automotive and aerospace applications. Researchers have been exploring novel aluminum matrix composites (AMC), which offer minimum wear rate for various tribological applications.
P. MUTHU
doaj +1 more source
Studying the Dry Sliding Wear for Composite Material of Base (Al-4%Cu) Reinforcement by Silicon Carbide Particles [PDF]
Engineering and Technology Journal, 2014 This work is concerned with a study of dry sliding wear of Aluminum bace alloy of (Al-4%Cu) reinforcement by silicon carbide particles with different percentage (3, 6,9,12 wt %SiC).
Ahmad Ali Akbar Akbar +2 more
doaj +1 more source
Formation and function of protective tribo-oxide layers on TC11 titanium alloy surface
Cailiao gongcheng, 2020 Dry sliding wear tests and specially designed double sliding wear tests of TC11 titanium alloys were carried out at sliding velocities of 2.68 m/s and 4 m/s by using a MPX-2000 type pin-on-disc wear tester.
LI Xin-xing +3 more
doaj +1 more source
Tribological Behavior of Ni-P Electroless Coating of Inconel 625 with Multiwall Nano Carbon Tubes
Advances in Materials Science and Engineering, 2023 An attempt was taken to study the wear rate of coated Inconel 625 using 0.3 gm of multiwall carbon tubes (MWCNT).The coating was carried out by the Ni-P electroless coating method. The Ni-P-MWCNT coating was prepared by using nickel phosphorous solution.
D. Jayabalakrishnan +7 more
doaj +1 more source
Scientific Reports, 2023 Wear properties of Al–Mg–Si alloy matrix hybrid composites made with Si-based refractory compounds (SBRC) derived from bamboo leaf ash (BLA) as complimentary reinforcement with alumina have been studied. The experimental result indicate that optimum wear
Olanrewaju S. Adesina +4 more
doaj +1 more source
Effect of reinforcing submicron SiC particles on the wear of electrolytic NiP coatings Part 2: Bi-directional sliding [PDF]
, 2006 As-plated and heat-treated electrodeposited NiP and composite NiP-SiC coatings were investigated in bi-directional ball-on-disc sliding tests. All tests were performed under gross slip conditions.
Aslanyan, I. R. +2 more
core +2 more sources