Results 21 to 30 of about 31,925 (313)
Wear maps for TiC composite based coatings deposited on 303 stainless steel [PDF]
, 2014 Dry sliding wear (pin-on-disc) tests were carried out under ambient conditions at room temperature for TiC coated and uncoated 303 stainless steel, using alumina as a counterface.
Rasool, Ghulam +3 more
core +1 more source
Experimental Study on Dry Friction Behavior of AlumiNm Alloy Casing
Shiyou jixie, 2022 In order to study the frictional and wear behavior of alumiNm alloy casing in gas drilling technology, under dry friction conditions, taking 40CrNmo steel as the pin and 7075 alumiNm alloy as the disc, by means of pin-disc wear test system, the effects ...
Xing Xuesong, Zhang Huizeng, Li Juan
doaj
Simulation and Experimental Research on the Failure of Marine Sliding Bearings
Journal of Marine Science and Engineering, 2023 The performance of the marine sliding bearing affects the reliability of marine engineering directly. Nevertheless, sliding bearings are subjected to frictional forces and problems, such as wear and fatigue, that occur after long-term use, which leads to
Fengming Du +4 more
doaj +1 more source
Predicting wear of UHMWPE: decreasing wear rate following a change in direction [PDF]
, 2011 Computational tools are emerging as design tools for the development of total joint replacement with improved wear performance. The current wear models of polyethylene assume that wear is linearly proportional to sliding distance; however, it is ...
Render, Todd D. +9 more
core +1 more source
Effect of Experimental Parameters on Wear Response of Thermally Sprayed Carbide Based Coatings [PDF]
Materials Research, 2018 Friction and abrasive wear response of WC-12 Co and Cr3C2-25 NiCr coatings was studied. Abrasive wear experiments were conducted with SiC abrasive particles with varying load and sliding speeds.
Nitesh Vashishtha, Sanjay Sapate
doaj +2 more sources
Fe nano-particle coatings for high temperature wear resistance [PDF]
, 2011 Oxidational wear continues to present an economic challenge for the replacement of components subject to high temperature fretting and sliding contacts in applications such as gas turbine engines.
S.R. Saranu +12 more
core +1 more source
Dry sliding wear characterization of squeeze cast LM13/FeCu composite using response surface methodology [PDF]
China Foundry, 2017 Dry sliding wear is one of the predominant factors to be considered while selecting material for automotive and aerospace applications. Researchers have been exploring novel aluminium matrix composites (AMC), which offer minimum wear rate for various ...
Samson Jerold Samuel Chelladurai +2 more
doaj +1 more source
Surface morphology in engineering applications: Influence of roughness on sliding and wear in dry fretting [PDF]
, 2011 Influence of initial surface roughness on friction and wear processes under fretting conditions was investigated experimentally. Rough surfaces (Ra=0.15-2.52 [mu]m) were prepared on two materials: carbon alloy (AISI 1034) and titanium alloy (Ti-6Al-4V ...
Mathia, T.G. +8 more
core +1 more source
Model of strain distribution by sliding wear
Wear, 1973 Abstract On the basis of a model it is possible to describe quantitatively the plastic deformation found in the surface zone of an oxygen free, high conductivity (OFHC) copper pin sliding against an SAE 1045 steel ring. The proposed model for this deformation type of wear can also be used for all deformation processes actuated by a shear stress on a
Dautzenberg, J.H., Zaat, J.H.
openaire +2 more sources
Advances in Materials Science and Engineering, 2022 Aluminum is among the most preferred materials based on the desired properties. This investigation focused on to evaluate the wear rate of the AA6066 aluminium alloy composite by using pin-on-disc apparatus.
T. Sathish +6 more
doaj +1 more source