Results 181 to 190 of about 380,995 (285)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Colorimetric detection of edible oil oxidation using PAN-Congo red nanofiber mats. [PDF]

Sci Rep
Hashim AF, Zahran HA, Afifi SM, Abd-Rabou AA, Hamed SF.   +4 more
europepmc   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Phytochemical Profiling and Antioxidant Activity of <i>Justicia thunbergioides</i> (Lindau) Leonard (Acanthaceae): A Promising Source of Therapeutic Metabolites. [PDF]

Pharmaceuticals (Basel)
Provensi LR, Carneiro MRB, Martins-Oliveira A, Porto ALM, Gil ES, Peixoto JC, Rosseto LP.   +6 more
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Pharmacophoric Investigation of a Natural Product-like Class of Aromatase Inhibitors Using Molecular Modeling. [PDF]

ACS Omega
Held A, Esselman A, Huebner M, Frietas G, Boyson B, Walker M, Miller B.   +6 more
europepmc   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Machine Learning Exploration of Food-Derived Chemical Space for Potential Nutritional Metabolic Regulators Targeting Dipeptidyl Peptidase-4. [PDF]

Pharmaceuticals (Basel)
Alzunaidy NA.
europepmc   +1 more source

Laser Metal Powder Deposition of Titanium Microalloyed HSLA Steel FeC0.12Si0.25Mn1.3

Advanced Engineering Materials, EarlyView.
This study investigates the additive manufacturing of titanium‐doped high‐strength low‐alloy (HSLA) steel via laser metal deposition. It reveals distinct process‐structure relationships for elemental powder blends compared to prealloyed feedstocks.
Olaf Stelling, Matthias Steinbacher, Nils Ellendt   +2 more
wiley   +1 more source