Results 101 to 110 of about 191,284 (340)

Modeling the deformation textures and microstructural evolutions of a Fe–Mn–C TWIP steel during tensile and shear testing [PDF]

, 2012
The high manganese austenitic steels with low stacking fault energy (SFE) present outstanding mechanical properties due to the occurrence of two strain mechanisms: dislocation glide and twinning. Both mechanisms are anisotropic.
Barbier, David, Bolle, Bernard, FAVIER, Véronique, BARBIER, D, BOLLE, B   +4 more
core   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Design exploration methodology for ultra thick laminated composites [PDF]

, 2012
Existing test and analytical methods (theoretical and numerical) are normally restricted to thin laminate components, which cannot accurately represent the 3D stress state behaviour of the so called Ultra Thick Laminates (UTL) structures.
Carrasco-Munoz Y Guerra, Jacinto
core  

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Control of Polarization and Polar Helicity in BiFeO3 by Epitaxial Strain and Interfacial Chemistry

Advanced Functional Materials, EarlyView.
In BiFeO3 thin films, the interplay of interfacial chemistry, electrostatics, and epitaxial strain is engineered to stabilize homohelicity in polarization textures at the domain scale. The synergistic use of a Bi2O2‐terminated Aurivillius buffer layer and a highly anisotropic compressive epitaxial strain offers new routes to control the polar‐texture ...
Elzbieta Gradauskaite, Lilia Huynh, Natascha Gray, Quintin N. Meier, Marta D. Rossell, Morgan Trassin   +5 more
wiley   +1 more source

Mechanical Behavior and Fracture Mechanisms of MXene/PVDF Nanocomponsites: In Situ Characterization and Multiscale Analysis

Advanced Functional Materials, EarlyView.
Multiscale experiments and modeling reveal how Ti3C2Tx MXene nanosheets reinforce PVDF nanocomposites. An optimal MXene loading (∼1 wt.%) nearly doubles tensile strength through efficient stress transfer, flake alignment, and crack‐deflection mechanisms, transforming ductile polymer behavior into a controlled multi‐stage fracture pathway which aligns ...
Bita Soltan Mohammadlou, James FitzPatrick, Li Meng, Kateryna Shevchuk, Ahmad Najafi, Yury Gogotsi   +5 more
wiley   +1 more source

Response of thin circular plates to central blast loading

, 1996
Includes bibliographical references.The large ductile deformation response and rupture of thin circular metal plates subjected to central blast loading is investigated using the ABAQUS general purpose finite element code.
Bimha, Richard Ernest
core  

Machine Learning‐Assisted Inverse Design of Soft and Multifunctional Hybrid Liquid Metal Composites

Advanced Functional Materials, EarlyView.
A machine learning framework is presented for inverse design of synthesizable multifunctional composites containing both liquid metal and solid inclusions. By integrating physics‐based modeling, data‐driven prediction, and Bayesian optimization, the approach enables intelligent design of experiments to identify optimal compositions and realize these ...
Lijun Zhou, Yunsik Ohm, Ren‐Mian Chin, Olivia Kerr, Krithika Manohar, Mohammad H. Malakooti   +5 more
wiley   +1 more source

Vibration and Stability of Variable Cross Section Thin-Walled Composite Shafts with Transverse Shear

Shock and Vibration, 2015
A dynamic model of composite shaft with variable cross section is presented. Free vibration equations of the variable cross section thin-walled composite shaft considering the effect of shear deformation are established based on a refined variational ...
Ma Jing-min, Ren Yong-sheng
doaj   +1 more source