Results 91 to 100 of about 19,781 (230)

Comparison of Recycled Polypropylene Sourced From Food and Nonfood Applications for Direct Food Contact Use

Packaging Technology and Science, Volume 39, Issue 6, Page 765-778, June 2026.
Utilisation of postconsumer recycled (PCR) plastic for food contact has safety concerns due to the potential presence of unapproved intentionally/non‐intentionally added substances, which can pose health and environmental risks if not removed during recycling.
Khairun Tumu, Keith Vorst, Greg Curtzwiler   +2 more
wiley   +1 more source

Fused Filament Fabrication and Recycling of Bio‐Based Polyamide 11 Reinforced With Recycled Short Carbon Fibers

Polymer Composites, Volume 47, Issue 9, Page 7909-7923, 10 May 2026.
Fused Filament Fabrication and Recycling of Bio‐Based Polyamide 11 Reinforced With Recycled Short Carbon Fibers. Sample preparation, mechanical properties improvement after rCF addition and properties retainment after recycling. ABSTRACT This research investigates the fused filament fabrication (FFF) and recycling of bio‐based polyamide 11 (PA11 ...
Mirko Coser, Daniele Rigotti, Alessandro Pegoretti   +2 more
wiley   +1 more source

Compartmental approach for modelling twin-screw granulation using population balances.

International journal of pharmaceutics, 2019
In this study, a compartmental population balance model (CPBM) is developed as a predictive tool of particle size distribution (PSD) for wet granulation in co-rotating twin-screw granulator (TSG).
hys 05, Saeed Shirazian, Mehakpreet Singh, D. Whitaker, Ahmad B. Albadarin, G. Walker   +5 more
semanticscholar   +1 more source

Development and scale- up of diversion strategy for Twin Screw Granulation in Continuous Manufacturing.

Journal of Pharmacy and Science, 2020
Successful implementation of Continuous Manufacturing technology requires real time product quality monitoring that can result into rejection strategies for material manufactured outside process control limits.
Pallavi Pawar, Donald J. Clancy, L. Gorringe, S. Barlow, A. Hesketh, R. Elkes   +5 more
semanticscholar   +1 more source

Integrating Eco‐Design Standards Into Assembly–Disassembly Requirements for Battery Pilot Line Processes

Advanced Energy and Sustainability Research, Volume 7, Issue 5, May 2026.
This article presents an eco‐design framework for battery development, linking raw materials, cell assembly design, implementation, module design, and recycling approach. It focuses on polymeric solid‐state in a pouch cell configuration for sustainability.
Rahmandhika Firdauzha Hary Hernandha, Daniela Fontana, Matteo Dotoli, Vito Borrelli, Mohammad Hossein Morshed Varzandeh, Nanna Bjerre‐Christensen, Andy Schena, Shubhadeep Pal, Fasil Getnet Molla, Inês Ribeiro, Joana Rosa Gouveia, Laurent Castro, Aurelie Gueguen, Nicola Boaretto, June Blanco, Marta Cazorla Soult, Andriy Kvasha, Rezvan Karimi, Kevin Voges, Mohamed Abdel‐Monem, Arno Kwade   +20 more
wiley   +1 more source

Mechanical Recycling of Biochar‐Filled Poly(lactic acid): A Study of Mechanical and Thermal Properties Supported by Meta‐Analysis

Macromolecular Materials and Engineering, Volume 311, Issue 5, May 2026.
Biochar‐filled poly(lactic) acid is mechanically recyclable with acceptable property retention after one reprocessing cycle, while five cycles significantly reduce strength and ductility. Thermal transition temperatures do not change, crystallinity increases, and cold crystallization temperature decreases.
Ábris Dávid Virág, Kerstin Müller, Ana Ramos‐Masana, Csenge Tóth   +3 more
wiley   +1 more source

A novel combination of machine learning models and metaheuristic algorithm to predict important parameters of twin screw wet granulation process

Alexandria Engineering Journal
Twin screw granulation (TSG) has recently been emerged as a novel approach for the continuous wet granulation of fine particles (i.e., powders) in the pharmaceutical industry. The presence of brilliant advantages like the ability of operation at very low
Tareq Nafea Alharby, Jowaher Alanazi, Muteb Alanazi, Bader Huwaimel   +3 more
doaj   +1 more source

New Materials for Additive Manufacturing: Thermal and Spectroscopic Analysis of pa 12–Clay Composites

Polymers for Advanced Technologies, Volume 37, Issue 5, May 2026.
ABSTRACT This study investigated the thermal and spectroscopic properties of composites produced from Polyamide 12 (PA 12) and montmorillonite (MMT) or sepiolite (SEP) clays, for application in additive manufacturing. These properties are critical during the printing process, as they directly affect the balance between the energy input to the parts and
Joyce Batista Azevedo, Ilana Oliveira Almeida, Eduardo Ferreira Alves Rocha, Lucas Nao Horiuchi, Talyta Silva Prado, Anna Imbriano, César Viseras, Rosana Fialho, Raquel de Melo Barbosa   +8 more
wiley   +1 more source

Discrete element method simulation of a twin screw wet granulator [PDF]

EPJ Web of Conferences
Granulation is a method of particle size enlargement via agglomeration of primary particles to form larger particles. In a Twin Screw Wet Granulator (TSWG), a binder liquid is sprayed onto the surfaces of active pharmaceutical ingredient particles to ...
Iyer Kiran, Wang Yu, Esteghamatian Amir, Meyer Ewald Jonathan, Doshi Pankaj, Wee Chuan Lim Eldin   +5 more
doaj   +1 more source

Overcoming Challenges in 3D Printing of Polyolefins and Their Composites: A Review on Strategies for Improved Printability and Performance

Polymer Engineering &Science, Volume 66, Issue 5, Page 3100-3141, May 2026.
This review integrates the molecular fundamentals, key challenges, and mitigation strategies in polyolefin 3D printing, focusing on shrinkage, warpage, and adhesion control. It highlights material design approaches using recycled polyolefins and functional fillers to improve printability, mechanical properties, and sustainability in additive ...
Malik Hassan, Philip McMorran, Marwan Eid, Julia Blair, Amar K. Mohanty, Manjusri Misra   +5 more
wiley   +1 more source