Results 1 to 10 of about 1,194 (216)
Simulation of moisture transfer during wood vacuum drying
Results in Physics, 2019 Vacuum techniques are commonly used in material drying applications as they provide good quality at fast rates. In this study, wood samples were dried under absolute pressure of 0.02 MPa at 80 °C to assess the drying characteristics.
Zhengbin He, Zhengbin He, Songlin Yi
exaly +3 more sources
Drying Stress and Strain of Wood: A Review
Applied Sciences, 2021 Wood drying stress causes various drying defects, which result from the wood microstructure and the transfer of heat and mass during the drying. It is the fundamental way to solve the problem of defects to clarify the law and mechanism of wood stress and
Qin Yin, Hong-Hai Liu
doaj +1 more source
Applied Sciences, 2021 The thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded.
Ivan Klement +6 more
doaj +1 more source
Jurnal Ilmu Kehutanan, 2009 Decreasing supply of most commercial depterocarp wood as raw material inspirates wood working industry producing building construction component to look for uncommercial wood to be utilized.
Yustinus Suranto
doaj +1 more source
Pengaruh Metode Pengeringan dan Jenis Sortimen Kayu Suren terhadap Kecepatan dan Cacat Pengeringan
Jurnal Ilmu Kehutanan, 2009 Effect of Drying Method and Lumber Dimension on Drying Rate and Defects of Suren Wood Efforts to improve productivity of wood industry must be supported by increasing supply of wood as raw materials.
Yustinus Suranto, Mugiyana Mugiyana
doaj +1 more source
Characteristics of Timbers Dried Using Kiln Drying and Radio Frequency-Vacuum Drying Systems
MATEC Web of Conferences, 2017 Heavy hardwoods are difficult-to-dry timbers as they are prone to checking and internal stresses when dried using a conventional kiln drying system. These timbers are usually dried naturally to reach 15% to 19% moisture content with an acceptable defects.
Rabidin Zairul Amin +2 more
doaj +1 more source
Drying of oak wood lamellas: Part 1. Analysis of the process in a dehumidification kiln [PDF]
Glasnik Šumarskog Fakulteta: Univerzitet u Beogradu, 2021 The subject of this paper is to analyse the drying process of oak lamellas, which are the solid wood top layer of engineered wood flooring. The focus of the first part of the paper is on dehumidification kilns.
Milić Goran +3 more
doaj +1 more source
Wood Drying In Construction [PDF]
The American Journal of Applied sciences, 2021 The article shows the indicators of the coefficients of shrinkage of wood, stages of shrinkage, the effect of the density of shrinkage of wood.
openaire +1 more source
International Journal of Applied Sciences and Smart Technologies, 2021 The purpose of this study is to determine the effect of the presence of a fan in the wood drying room in the drying time of wood. In addition, it is also to determine the performance of the steam compression cycle engine used in wood drying machines and ...
Wibowo Kusbandono +1 more
doaj +1 more source
HUBUNGAN SIFAT DASAR DAN SIFAT PENGERINGAN LIMA JENIS KAYU ANDALAN JAWA BARAT
Jurnal Penelitian Hasil Hutan (Journal of Forest Products Research), 2017 This study was intended to investigate the relation between basic properties and drying properties of five priority wood species, i.e. pulai kongo (Alstonia congensis Engl.), kibawang (Azadirachta excelsa Jack.), salamander (Grevillea robusta A.Gunn ...
Efrida Basri, Nurwati Hadjib
doaj +1 more source