Results 41 to 50 of about 25,901 (208)

ASCA Observations of Transient X-Ray Sources in Quiescence [PDF]

Publications of the Astronomical Society of Japan, 1998
Soft X-ray transients are most probably low-mass binary systems containing either a neutron star (NS-LMXB) or a black hole (BH-LMXB). We have systematically investigated thirteen soft X-ray transients (four NS-LMXBs and nine BH-LMXBs) in the quiescent state using the available ASCA data.
Kazumi Asai, Tadayasu Dotani, Reiun Hoshi, Yasuo Tanaka, Craig R. Robinson, Kentaro Terada   +5 more
openaire   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Origin of the X‐Ray Quasi‐periodic Oscillations and Identification of a Transient Ultraluminous X‐Ray Source in M82 [PDF]

The Astrophysical Journal, 2007
The starburst galaxy M82 contains two ultraluminous X-ray sources (ULXs), CXOM82 J095550.2+694047 (=X41.4+60) and CXOM82 J095551.1+694045 (=X42.3+59), which are unresolved by XMM-Newton. We revisited the two XMM-Newton observations of M82 and analyzed the surface brightness profiles using the known Chandra source positions.
Feng, Hua, Kaaret, Philip
openaire   +2 more sources

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Transient X-Ray Sources in the Magellanic-type Galaxy NGC 4449 [PDF]

The Astrophysical Journal, 2017
Abstract We report the identification of seven transient X-ray sources in the nearby Magellanic-type galaxy NGC 4449 using archival multi-epoch X-ray observations conducted with the Chandra, XMM-Newton, and Swift telescopes over the years 2001–2013. Among them, two sources are classified as supersoft X-ray sources (SSSs) because of their
V. Jithesh, Zhongxiang Wang
openaire   +2 more sources

Nonthermal Plasma Reduction of Nickel Oxide Layers by Atmospheric Pressure Dielectric Barrier Discharge in Argon/Hydrogen

Advanced Engineering Materials, EarlyView.
This work explores the reduction of nickel oxide layers using dielectric barrier discharge plasma in an argon–hydrogen atmosphere. The results reveal a strong temperature dependence, enabling complete reduction of thick oxide layers at 200°C within seconds.
Maria Argirusi, Viktor Udachin, Sascha Jan Zimmermann, Alexander Tillmanns, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +5 more
wiley   +1 more source

Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines

Advanced Engineering Materials, EarlyView.
Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl, Daniel Emil Mack, Martin Tandler, Susanne Schrüfer, Robert Vaßen   +4 more
wiley   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source