Results 51 to 60 of about 53,047 (263)

THE IMPACT OF VEHICLE LOAD INDUCING VIBRATIONS ON THE SUBGRADE SOIL PARTICLE ACCELERATION [PDF]

Journal of Engineering Science and Technology, 2018
This paper revealed the description of subgrade soil particles vibration induced by vehicles. A field investigation has been conducted to obtain the comprehensive understanding about the behaviour of soil particles vibration by analyzing the interaction ...
RINI KUSUMAWARDANI, UNTORO NUGROHO, MUHAMMAD HAMZAH FANSURI, TIGO MINDIASTIWI, WORO YUNIARTI, AKHRIS SUFRI HILMI   +5 more
doaj  

Effect of terahertz irradiation on DNA damage repair in living cells

FEBS Open Bio, EarlyView.
We investigated the effect of terahertz (THz) wave irradiation on DNA double‐strand break (DSB) repair in living cells. We found that THz irradiation enhanced DSB repair at specific frequencies, whereas heat treatment inhibited it, indicating that this effect is nonthermal and frequency‐specific.
Yuya Ueno, Shota Yamazaki, Hiromichi Hoshina, Masahiko Harata   +3 more
wiley   +1 more source

Mutant NPM1 in Acute Myeloid Leukemia Initiation and Maintenance

Aging and Cancer, EarlyView.
NPM1 mutations drive acute myeloid leukemia by acting as neomorphic transcriptional regulators that cooperate with Menin–MLL and XPO1 to sustain HOX/MEIS1 expression and block differentiation. Targeting these mutant‐specific transcriptional dependencies provides a rational therapeutic strategy for NPM1‐mutated AML.
Yanan Jiang, Zhong Fan, Runmeng Liu, Xiaotian Zhang   +3 more
wiley   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Dispersion of Aggregate Particles by Acceleration in Air Stream [Translated]†

KONA Powder and Particle Journal, 2014
To clarify the dispersion mechanisms of aggregate particles in air, the dispersion of aggregate particles by acceleration in an air stream, which is a typical dispersion mechanism, was examined.
Yasuo Kousaka, Yoshiyuki Endo, Takahiro Horiuchi, Tohru Niida   +3 more
doaj   +1 more source

Characterization of Aluminized Layers on Inconel‐738 Alloy: Microstructure, Modeling of Aluminizing Kinetics, and Thermal Behavior

Advanced Engineering Materials, EarlyView.
This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe, Tuba Yener, Suayb Cagri Yener, Mourad Keddam, Cuma Bindal   +4 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Enhancing Strength and Electrical Conductivity in Al–Zr–Sc Conductor Alloys Through Sn and Sr Microalloying and Two‐Step Aging Treatment

Advanced Engineering Materials, EarlyView.
Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao, Emad M. Elgallad, Alexandre Maltais, X.‐Grant Chen   +3 more
wiley   +1 more source