Results 41 to 50 of about 1,205,694 (311)

Effect of Fe Content on the Microstructure and Properties of 5083 Aluminum Alloy

Crystals
To address the challenge of controlling Fe impurity content during the recycling of aluminum alloys, this study utilized commercial 5083 aluminum alloy as a matrix to prepare alloy samples with four different Fe contents via smelting.
Jun Cao, Wenjia Zhao, Jiaxing Li, Hongqun Tang, Xu Zheng, Kezhun He, Qizhong Zhao, Hongchi Yang, Xianye Lu, Shengyuan Lei, Chunhua Wei   +10 more
doaj   +1 more source

Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects

Advanced Engineering Materials, EarlyView.
This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula, Gökhan Küçüktürk, Duran Kaya, David Grossin, Christophe Tenailleau, Benjamin Duployer, Enrique Juste, Fabrice Petit   +7 more
wiley   +1 more source

Effects of the surface properties and particle size of hydrated lime on desulfurization

Cleaner Materials
In the gas treatment center in smelters, hydrogen fluoride (HF) is separated from the outlet gases of electrolysis cells, which are used to produce aluminum from alumina. However, SO2 largely remains in the effluent gas.
Karthikeyan Rajan, Duygu Kocaefe, Yasar Kocaefe, Jonathan Bernier, Yoann Robert, Yves Dargis   +5 more
doaj   +1 more source

Use of Aluminum-Foil and Oat-Straw Mulches for Controlling Aster Leafhopper, \u3ci\u3eMacrosteles Fascifrons\u3c/i\u3e (Homoptera: Cicadellidae), and Aster Yellows in Carrots. [PDF]

, 2017
Aluminum-foil and oat-straw mulches significantly (P \u3c 0.05) reduced aster leafhopper numbers on carrots compared to an untreated control and a malathion spray treatment during the first half of the growing season.
Ragsdale, David W, Setiawan, Dwi P
core   +2 more sources

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Multi-Time Optimization Scheduling Strategy for Integrated Energy Systems Considering Multiple Controllable Loads and Carbon Capture Plants

Energies
In response to the dual carbon targets, it is necessary not only to reduce carbon emissions but also to increase the proportion of renewable energy generation capacity, thereby exacerbating the scarcity of flexible resources in the power system ...
Zhe Han, Zehua Li, Wenbo Wang, Wei Liu, Qiang Ma, Sidong Sun, Haiyang Liu, Qiang Zhang, Yue Cao   +8 more
doaj   +1 more source

Thin-film ultraviolet detector and spectrometer [PDF]

, 1972
Typical metal-insulator-metal detector device is formed on quartz substrate. Base electrode is 3 to 6 nm aluminum layer, overcoated with 3 to 6 nm aluminum oxide or aluminum nitride, and capped with counter electrode of gold, lead, magnesium, or aluminum.
Lewicki, G. W., Maserjian, J.
core   +1 more source

Characterization of Aluminized Layers on Inconel‐738 Alloy: Microstructure, Modeling of Aluminizing Kinetics, and Thermal Behavior

Advanced Engineering Materials, EarlyView.
This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe, Tuba Yener, Suayb Cagri Yener, Mourad Keddam, Cuma Bindal   +4 more
wiley   +1 more source

Inhomogeneity of Microstructure and Properties of 7085-T651 Aluminum Alloy Extra-thick Plate

Journal of Aeronautical Materials, 2016
Inhomogeneity of microstructure and properties of 7085-T651 aluminum alloy extra-thick plate were investigated by tensile properties, exfoliation corrosion, optical microscopy(OM), composition analysis, scanning electron microscopy(SEM),differential ...
LI Chengbo, HE Kezhun, SONG Fengxuan, LIU Shengdan, CAO Shengqiang, ZHANG Xinming   +5 more
doaj   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source