Results 51 to 60 of about 269,191 (267)

Mixed-mode growth of a multicomponent precipitate in the quasi-steady state regime

Materials Theory, 2018
An exact analytical solution of the Fick’s second law was developed and applied to the mixed-mode growth of a multicomponent ellipsoidal precipitate growing with constant eccentricities in the quasi-stationary regime. The solution is exact if the nominal
Tohid Naseri, Daniel Larouche, Rémi Martinez, Francis Breton   +3 more
doaj   +1 more source

Enhancing Strength and Electrical Conductivity in Al–Zr–Sc Conductor Alloys Through Sn and Sr Microalloying and Two‐Step Aging Treatment

Advanced Engineering Materials, EarlyView.
Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao, Emad M. Elgallad, Alexandre Maltais, X.‐Grant Chen   +3 more
wiley   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source

Mechanical properties and fracture behavior of Al(111)/MgAlB4(0001) interface in Al matrix composites: a first-principle calculation study

Materials Research Express, 2023
Hexagonal crystal MgAlB _4 is a strengthening phase in Al matrix composites, which can significantly improve ultimate tensile strength. In this paper, the surface perform, interfacial bonding characteristic, fracture mechanism, and electronic properties ...
Mingjie Wang, Yijie Zhang, Hongxing Zheng, Zhongyun Ru, Xiaoyu Yang   +4 more
doaj   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio

Advanced Engineering Materials, EarlyView.
This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov, Matheus Roberto Bellé, Anton Yehorov, Julia Richter, Olena Volkova   +4 more
wiley   +1 more source

Influence of Preaging Treatment on Bake-Hardening Response and Electrochemical Corrosion Behavior of High Strength Al-Zn-Mg-Cu-Zr Alloy

Metals, 2019
The influence of preaging (PA) treatments on the bake hardening (BH) response of a AlZnMgCuZr aluminum alloy which served as automotive body structures were studied in this paper.
Hui Li, Xiao-Teng Liu, Jia-Yi Wang
doaj   +1 more source

Preparation of Aluminum Nitride/Aluminum Composites by Nitridation of Aluminum

Journal of the Ceramic Society of Japan, 1993
AlN/Al composites were prepared by the nitridation of Al-MgO (0-7.5wt%) powder compacts at 1100-1400°C. The dense composite layer grew outward from the bottom surface of the powder compact at 1250-1400°C. The conversion of Al to AlN and the thickness of the composite increased with increasing content of MgO, reaction temperature and time.
Keita INOUE, Takanori WATARI, Toshio TORIKAI, Ohsaku MATSUDA   +3 more
openaire   +2 more sources