Results 51 to 60 of about 2,658 (208)
Thin Wall Ductile Iron Castings: Technological Aspects [PDF]
, 2013 The paper discusses the reasons for the current trend of substituting ductile iron castings by aluminum alloys castings.However, it has been shown that ductile iron is superior to aluminum alloys in many applications.
E Fraś, M. Górny, W. Kapturkiewicz
core +2 more sources
steel research international, Volume 96, Issue 2, February 2025.A low‐carbon (0.23 wt%) carbide‐free bainitic steel is successfully developed with a total alloying addition of 4.9 wt%, which is relatively lower than alloying additions reported in similar category of steels. The present findings indicate that the currently designed low‐alloy steel composition is amenable to generation of nearly carbide‐free bainitic
Poulami Chakraborty +8 more
wiley +1 more source
International Scholarly Research Notices, Volume 2011, Issue 1, 2011., 2011 Taking into account the importance of the amount of bainite phase on the microstructure of cast irons and its influence on the improvement of mechanical properties, this research selected an alloy of gray cast iron containing Nickel‐Molybdenum and conducted the austenitising and austempering processes at 900°C and 400°C for 60 minutes, respectively ...
A. R. Kiani-Rashid +4 more
wiley +1 more source
Damping Performance of Manganese Alloyed Austempered Ductile Iron
Applied SciencesAustempered ductile iron has gained increased interest as an ideal choice of material for mechanical components exposed to dynamic loading. Apart from strength and ductility, material damping is also one of the important demands imposed on the machine ...
Umanath R. Poojary +2 more
doaj +1 more source
Sliding wear behavior of PVD CrN and TiN coated austempered ductile iron [PDF]
, 2014 This work studies the sliding wear behavior of PVD coated austempered ductile iron samples. The effects of the substrate surface finishing method (grinding and polishing) and coating material (CrN and TiN) on the wear behavior are evaluated.
Colombo, Diego Alejandro +4 more
core +2 more sources
The Effect of Cryogenic Treatment on W360 and E38K Hot Work Tool Steels
steel research international, Volume 95, Issue 9, September 2024.The cryogenic treatment facilitates the transformation of retained austenite to martensite to an undetectable limit, with about 3 times higher amount of the carbide precipitation for both steel types. Both steel types exhibit almost similar impact energy values at room temperature, but E38K steel has 2 times higher energy at 350 °C.
Caner Kiraz, Burak Birol, Ahmet Sağın
wiley +1 more source
Characteristics of ADI Ductile Cast Iron with Single Addition of 1.56% Ni
Archives of Metallurgy and Materials, 2017 The results of examinations of microstructure and an analysis of its impact on selected mechanical properties of austempered ductile iron (ADI) were presented in the paper.
Mrzygłód B. +4 more
doaj +1 more source
Microstructural Characterization and Some Mechanical Behaviour of Low Manganese Austempered Ferritic Ductile Iron [PDF]
, 2017 This work studied the microstructural characterization and mechanical behavior of low manganese Austempered Ductile Iron (ADI), with a view to improve the properties of iron and to increase the areas of applications.
Abioye, Abiodun A. +4 more
core +2 more sources
INCREASING THE SURFACE HARDNESS OF CAST IRON BY ELECTRODEPOSITION OF BORIDES IN MOLTEN SALTS [PDF]
, 2017 In this paper the electrodeposition of boron on the surface of cast iron as a coating is applied to increase the hardness and protect the substrate against abrasive wear.
Al-Azzawi, Ali H. +2 more
core +1 more source
Austenitization of FerriticDuctile Iron
Archives of Foundry Engineering, 2014 Austenitization is the first step of heat treatment preceding the isothermal quenching of ductile iron in austempered ductile iron (ADI) manufacturing. Usually, the starting material for the ADI production is ductile iron with more convenient pearlitic ...
Krzyńska A., Kochański A.
doaj +1 more source