Results 61 to 70 of about 363,714 (297)
Journal of Materials Research and TechnologyThe amorphous/crystalline (A/C) dual-phase structure is a new design strategy to improve the comprehensive performance of Mg alloys. However, the regulation mechanism of the amorphous phase size of the dual-phase Mg alloys is still unclear.
X.Y. Li, H.Y. Song, Y.L. Li
doaj +1 more source
Quantum atomic delocalization vs. structural disorder in amorphous silicon
, 1998 Quantum effects on the atom delocalization in amorphous silicon have been studied by path-integral Monte Carlo simulations from 30 to 800 K. The quantum delocalization is appreciable vs.
C. P Herrero +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Elinvar Materials: Recent Progress and Challenges
Advanced Engineering Materials, EarlyView.Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley +1 more source
Antioxidants, 2021 In this study, we designed amorphous solid dispersions based on Eudragit E/HCl (neutralized Eudragit E using hydrochloric acid) to maximize the dissolution of trans-resveratrol.
Eun-Sol Ha +4 more
doaj +1 more source
Avalanche Size Scaling in Sheared Three-Dimensional Amorphous Solid [PDF]
, 2007 We have studied the statistics of plastic rearrangement events in a simulated amorphous solid at T=0. Events are characterized by the energy release and the ``slip volume'', the product of plastic strain and system volume. Their distributions for a given
A. Inoue +8 more
core +6 more sources
Leggett’s bound for amorphous solids
Physical Review B, 2011 We investigate the constraints on the superfluid fraction of an amorphous solid following from an upper bound derived by Leggett. In order to accomplish this, we use as input density profiles generated for amorphous solids in a variety of different manners including by investigating Gaussian fluctuations around classical results.
Biroli, Giulio +3 more
openaire +3 more sources
Advanced Engineering Materials, EarlyView.This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Drug-excipient behavior in polymeric amorphous solid dispersions
Journal of Excipients and Food Chemicals, 2016 Amorphous drug delivery systems are increasingly utilized to enhance aqueous solubility and oral bioavailability. However, they lack physical and/or chemical stability.
Surikutchi Bhanu Teja +4 more
doaj