Results 111 to 120 of about 96,622 (267)
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories
Advanced Engineering Materials, EarlyView.Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Adequacy of surface analytical tools for studying the tribology of ceramics [PDF]
Surface analytical tools are very beneficial in tribological studies of ceramics. Traditional methods of optical microscopy, XRD, XRF, and SEM should be combined with newer surface sensitive techniques especially AES and XPS.
Sliney, H. E.
core +1 more source
Physical Stability and Viscoelastic Properties of Co-Amorphous Ezetimibe/Simvastatin System [PDF]
, 2019 The purpose of this paper is to examine the physical stability as well as viscoelastic properties of the binary amorphous ezetimibe–simvastatin system.
Chmiel, Krzysztof +5 more
core +2 more sources
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Preparation and characterization of multi-component tablets containing co-amorphous salts : Combining multimodal non-linear optical imaging with established analytical methods [PDF]
, 2018 Co-amorphous mixtures have rarely been formulated as oral dosage forms, even though they have been shown to stabilize amorphous drugs in the solid state and enhance the dissolution properties of poorly soluble drugs.
Korhonen, Ossi +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm +6 more
wiley +1 more source
Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions
Advanced Engineering Materials, EarlyView.This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel +6 more
wiley +1 more source