Results 81 to 90 of about 47,157 (266)

Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators

Advanced Engineering Materials, EarlyView.
A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad, Aleksander Kostka, Gowtham Arivanandhan, Yujiao Li, Alan Savan, Manfred Kohl, Alfred Ludwig   +6 more
wiley   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Increasing the content of CSL grain boundaries in ferritic steel through grain boundary engineering

Journal of Materials Research and Technology
Coincidence Site Lattice (CSL) grain boundaries are special boundaries that enhance a material’s resistance to hydrogen embrittlement, corrosion, and fracture.
Onur Can Şen, Santiago Benito, Sebastian Weber, Rebecca Janisch   +3 more
doaj   +1 more source

On the effect of boron on the mechanical properties of a new polycrystalline superalloy

MATEC Web of Conferences, 2014
Boron is used as a grain boundary strengthener in the nickel-based superalloys, but the reasons for its effect and the optimum quantities which need to be added are not well understood.
Kontis Paraskevas, Mohd Yusof Hanis A., Moore Katie L., Grovenor Chris R.M., Reed Roger C.   +4 more
doaj   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Modular Critical Element Recycling Platform Using a Nanoporous Additively Manufactured Gyroid

Advanced Engineering Materials, EarlyView.
A modular recycling platform integrates 3D‐printed nanoporous gyroid structures to enable efficient critical element recovery. This system utilizes a hierarchical architecture, combining macroscopic channels with polymerization‐induced nanoscale porosity. By systematically tuning structural wall thickness and resin formulation, the platform achieves an
Xiangyu Gao, Keldy Mason, Mert Gülçür, Rachel Paddock‐Lamb, Prince Alvin Fofanah, Zachariah A. Page, Michael Cullinan   +6 more
wiley   +1 more source

Revealing the temperature-dependent cyclic plasticity and failure mechanisms in GH4169 nickel-based superalloy

Materials & Design
The low-cycle fatigue behavior and associated microstructural evolution of GH4169 nickel-based superalloy were systematically investigated at elevated temperatures.
Xipeng Yin, Ming Li, Yan Wang, Dan Feng, Xiufang Gong, Zhixun Wen, Zhufeng Yue, Wei Sun   +7 more
doaj   +1 more source