Results 231 to 240 of about 2,488,943 (332)

A Thermodynamic 3D Model for the Simulation of Diffusion‐Controlled Alloying Processes in Heterogeneous Material Structures

Advanced Engineering Materials, EarlyView.
A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer, Leonhard Holländer, André Langohr, Hans Jürgen Maier   +3 more
wiley   +1 more source

Effects of nuclear interaction corrections and trichrome fragment spectra modelling on dose and linear energy transfer distributions in carbon ion radiotherapy. [PDF]

Phys Imaging Radiat Oncol
Bazani A, Brunner J, Russo S, Carlino A, Simon Colomar D, Ikegami Andersson W, Ciocca M, Stock M, Fossati P, Orlandi E, Glimelius L, Molinelli S, Knäusl B.   +12 more
europepmc   +1 more source

Influence of dose-averaged linear energy transfer on tumour control after carbon-ion radiation therapy for pancreatic cancer. [PDF]

Clin Transl Radiat Oncol, 2020
Hagiwara Y, Bhattacharyya T, Matsufuji N, Isozaki Y, Takiyama H, Nemoto K, Tsuji H, Yamada S.   +7 more
europepmc   +1 more source

Influence of Sample Preparation and Processing Procedures on the Thermal Diffusivity of MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan, Rhena Wulf, Till M. J. Stadtmüller, Christos G. Aneziris, Tobias M. Fieback   +4 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma

Advanced Engineering Materials, EarlyView.
The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie, David Kramer, Thomas Scheithauer, Hans Jürgen Maier, Thomas Hassel   +4 more
wiley   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source