Results 191 to 200 of about 128,995 (308)

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Influence of Drug Properties, Formulation Composition, and Processing Parameters on the Stability and Dissolution Performance of Amorphous Solid Dispersions-Based Tablets. [PDF]

Polymers (Basel)
Pantazos I, Poimenidou M, Kouskouridas D, Tzaferas E, Karava V, Cholevas C, Kapourani A, Barmpalexis P.   +7 more
europepmc   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

High-Throughput Microarray Approaches for Predicting the Stability of Drug-Polymer Solid Dispersions. [PDF]

Mol Pharm
Ghazi NF, Burley JC, Dryden IL, Roberts CJ.   +3 more
europepmc   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Impact of Polymer Physicochemical Features on the Amorphization and Crystallization of Citric Acid in Solid Dispersions. [PDF]

Polymers (Basel)
Arioglu-Tuncil S, Mauer LJ.
europepmc   +1 more source

Engineering Deformation and Failure in Diamond Triply Periodic Minimal Surface Lattices via 3D Wall‐Thickness Grading

Advanced Engineering Materials, EarlyView.
The work demonstrates that strategic wall‐thickness grading in diamond triply periodic minimal surface lattices enables precise tuning of deformation and failure behavior under compression. Different gradation patterns guide how and where the structure collapses, improving energy absorption or promoting controlled brittle failure.
Giovanni Rizza, Danilo Bruson, Manuela Galati, Luca Iuliano   +3 more
wiley   +1 more source

Enhancing drug administration in <i>Drosophila melanogaster</i>: a method for using solid dispersions for improved solubility and bioavailability. [PDF]

Fly (Austin)
Cheku S, Rokusek B, Pattabiraman M, Carlson KA.   +3 more
europepmc   +1 more source

3D‐Printed Serial Snap‐Through Architectures for Programmable Mechanical Response

Advanced Engineering Materials, EarlyView.
A serial snap‐through architecture is realized using compact 3D‐printed von Mises truss units arranged in a staged cascade. Their geometry and boundary conditions program multistage mechanical responses with plateaux and re‐hardening regimes. An inverted‐compliance model predicts these behaviors and enables analytical design of programmable force ...
Filipe A. Santos
wiley   +1 more source

Exploring the Relationship Between Stability and Dynamics in Polymer-Based Amorphous Solid Dispersions for Pharmaceutical Applications. [PDF]

Polymers (Basel)
Dudognon E, Bama JA, Affouard F.
europepmc   +1 more source